Частотные преобразователи HYUNDAI N500 от 200 до 350 кВт
Обновленная серия N500 мощных и компактных частотных преобразователей с функцией полного векторного контроля в общепромышленном исполнении и суперэкономичная серия для насосов и вентиляторов N500P.
(1) N500 Стандартные модели(CT-TYPE)
|
Model (N500 - □□□□HF) |
1600HF |
2200HF |
2800HF |
3500HF | |
|
Мощность мотора(4P, KW) |
160 |
220 |
280 |
350 | |
|
Полная мощность(KVA) |
400V |
232 |
318 |
400 |
500 |
|
Входное напряжение |
3 фазы380 ~ 480V ±10%, 50Hz / 60Hz | ||||
|
Выходное напряжение |
3 фазы(3-wire) 380 ~ | ||||
|
Выходной ток(A) |
304 |
418 |
525 |
656 | |
|
Выходная частота(Hz) |
0~400Hz | ||||
|
Перегрузка |
150% for the 60 seconds | ||||
|
Торможение |
опционально | ||||
|
Вес(Kg) |
200 |
215 | |||
|
Размер |
900 ×670 ×380 |
1080 ×650 ×380 |
1150 ×800 ×380 | ||
(2) N500-P экономичная серия (VT-TYPE)
|
Модель (N500 - □□□□HFP) |
2000HFP |
2800HFP |
3200HFP |
3800HFP | |
|
Мощность мотора(4P, KW) |
200 |
280 |
320 |
380 | |
|
Полная мощность (KVA) |
400V |
|
|
460 |
550 |
|
Входное напряжение |
3 Phase(3-wire) 380 ~ 480V ±10%, 50Hz / 60Hz | ||||
|
Выходное напряжение |
3 Phase(3-wire) 380 ~ 480V ( According to supply voltage ) | ||||
|
Выходной ток(A) |
397 |
532 |
616 |
732 | |
|
Выходная частота(Hz) |
0~400Hz | ||||
|
Перегрузка |
120% for the 60 seconds | ||||
|
Торможение |
опционально | ||||
|
Вес(Kg) |
200 |
215 | |||
|
Размер |
900 × 670 × 380 |
1080 × 650 × 380 |
1150 × 800 × 380 | ||
(3) Спецификация
|
Model (N500 - □□□□HF□) |
Specifications |
| ||
|
Voltage Modulation method |
SVPWM(Space Vector PWM) |
| ||
|
Frequency accuracy |
Digital : ±0.01% of maximum frequency, Analog : ±0.2%( 25±10℃) |
| ||
|
Frequency resolution |
Digital setting : 0.01Hz, Analog setting : Maximum frequency/4,000( 0-L : 12bit/0~10V, 02-L : -10~+10V ) |
| ||
|
voltage/frequency characteristic |
V/f Control(Constant torque and reduced torque), Sensorless vector control, Sensored vector control |
| ||
|
Accel/Decel time |
0.01 ~ 3,600seconds ( Linear/curve selection) |
| ||
|
Input signals |
Frequency setting |
Operator |
Set by UP / DOWN key |
|
|
External signal |
DC0 ~ 10V, -10V ~ +10V(Input impedance 10㏀), 4 ~ 20mA(Input impedance 100Ω) |
| ||
|
External port |
Set by RS485/232 |
| ||
|
Forward/ Reverse RUN/STOP
|
Operator |
FWD(Forward)/REV(Reverse) key |
| |
|
External signal |
FWD/REV run(N.O./N.C. contact) |
| ||
|
External port |
Set by RS485/RS232 communication |
| ||
|
Intelligent input terminals |
Selectable 8 intelligent terminal : FWD(Forward Run command), REV(Reverse Run command), CF1~CF4(Multi-stage operation 1~4), JOG(Jogging), DB(External DC Braking), 2CH(2-stage accel/decel), FRS(Free run stop), EXT(External trip), USP(Unattended start protection), CS(Change to/from commercial power supply), SFT(Software lock), AT(Analog input selection), RS(Reset), PID(PID on/off), PID_C(PID reset), UP(Remote controlled accel.), DOWN(Remote controlled decel.), UDCLR(Remote controlled data clearing) |
| ||
|
Thermister input terminal |
One terminal( PTC characteristic) |
| ||
|
Output signals
|
Intelligent output terminals |
Five open collector terminals and two relay output selectable : RUN(Run signal), FA1(Frequency arrival signal at the constant speed), FA2(Frequency arrival signal above the set frequency), OL(Overload advance notice signal), OD(Output deviation for PID control), AL(Alarm signal), FA3(frequency arrival signal only at the set frequency), IPS(Instantaneous power failure signal ), THM(Thermal alarm) |
| |
|
Monitor output terminals |
Analog voltage, Analog current, Pulse line output |
| ||
|
Display monitor |
Output frequency/current/voltage, Motor rotational speed, terminal status, output power, time, trip history |
| ||
|
Etc. |
V/f free setting(7-point), frequency limit, frequency jump, auto/manual torque boost, analog meter setting, start frequency, carrier frequency, electronic thermal, external frequency input via start/end, analog input selection, retry after trip, restart after instantaneous power failure, overload restriction, AVR function, auto-tuning, deceleration and stop power failure |
| ||
|
Carrier frequency setting |
2~4kHz |
| ||
|
Protection functions |
over current/voltage protection, under voltage protection, electronic thermal, over temperature, ground fault, instantaneous power failure, USP error, phase failure protection, IGBT error, external trip, communication error |
| ||
|
environmental conditions
|
Ambient operating/ storage temperature /humidity |
-10 ~ 50℃ /-20~65℃/ 20 ~ 90% RH(Non-condensing) |
| |
|
Vibration |
2.94m/s2( 0.3G ), 10 ~ 55Hz( 22KW ) |
| ||
|
Location |
Less than 1,000m of altitude, indoor( no corrosive gas nor gust) |
| ||
|
Color |
Gray(Munsell 8.5 YR 6.2/0.2) |
| ||
|
Protection class |
IP20(NEMA1) |
| ||
|
Option
|
Cable |
Connection cable ICS-3(3m) |
| |
|
ETC. |
AC reactor(input/output), DC reactor, EMI filter, Radio noise filter, Braking unit, Braking resistor, LCR filter | |||